What is FaradFlex®? 
What does FaradFlex® do? How is it used?
Who should utilize FaradFlex® ?
What applications does FaradFlex® target?
Is a Buried CapacitanceTM license required to use FaradFlex®?
How many capacitors can be removed by using FaradFlex®?
What is the impact on the cost of the PCB/ PCBA/ System?
Is FaradFlex® robust to lead free processing?
Can PCB shops process ultra thin materials with out added cost?
What PCB shops can use FaradFlex®?
What materials are compatible with FaradFlex®?

What is FaradFlex®?
FaradFlex® is an ultra-thin, high performance “family” of laminates used for low impedance, low inductance, and/ or embedded capacitance in printed circuit boards, chip package substrates, modules, and other electronic applications. 
>back to top

What does FaradFlex® do? How is it used?
The material components of FaradFlex® have properties which make the laminate unique at providing low impedance, high capacitance, and high reliability at substrate thicknesses of 1.0 mil (25 micron) down to as thin as 0.33 mil (8 micron). FaradFlex® typically is used as a layer or layers in a printed circuit board. Most often the FaradFlex layers are designed as “paired” power/ ground layers which allow it to act as a capacitor. For optimum benefit and lowest impedance, FaradFlex® is designed into a stack up close to the top and bottom layers of the PCB. For embedded capacitance, via hole connections are placed in the PCB down to the FaradFlex layer connecting to the active IC’s and eliminating the need to for most or all the 0.1 µf or 0.01 µf bypass capacitors. This also eliminates the need for the bypass capacitor pads, traces, and vias. FaradFlex® can be used to significantly reduce the overall thickness of the PCB which can be a major design benefit.
>back to top

Who should utilize FaradFlex®?
The most common beneficiaries of FaradFlex® are OEM’s designing PCBs, modules, and chip packaging substrates. Although the OEM designers don’t typically buy PCB materials, they do determine the benefits and decide on the PCB requirements for EMI, signal integrity, power integrity, size, weight, reliability, lead free, “green”, and performance. FaradFlex® allows the designer to achieve superior benefits for the above requirements that cannot be achieved using other materials and methodologies. Finally, the designer typically will work with a PCB fabricator/ purchaser to use FaradFlex® in the designer’s PCB. 
>back to top

What applications does FaradFlex® target?
FaradFlex solves many PCB, chip packaging, and module performance issues. Common solutions using FaradFlex® include:

  1. Eliminate resonance/ noise/ EMI from difficult PCB, modules, and module devices.
  2. Remove bypass capacitors from a dense and crowded PCB. Along with the capacitor removal, also removing 2 traces, pads, and via holes for each device. This allows room for other devices and new functionality. Also, it allows the PCB to be reduced in layers or dimensions if needed.
  3. Provide much improved power delivery by greatly reducing the inductance loop to an absolute minimum.
  4. Improve signal and power integrity.
  5. Improve reliability due to the elimination of many small capacitors and solder joints. The polymer film in most of the FaradFlex® constructions is more robust to CAF as well as dielectric breakdown.
  6. Lower cost for the system and even the PCB. Although the laminate may have a higher cost than typical FR-4 laminates, using FaradFlex® in many cases allows the PCB to be reduced in size or layer count. This can provide more PCB’s per panel at the fabricator. Additionally, there is a savings associated with eliminating the discrete capacitors and corresponding assembly.
  7. Allows for thinner PCBs or additional layers to be incorporated with little or no impact on overall thickness. Plating yields can be improved by reducing the aspect ratio, as well as letting existing connectors be used while increasing layer count. 

>back to top

Is a Buried CapacitanceTM license required to use FaradFlex®?
The OEM/ designer does not need a license to use FaradFlex in their design. The PCB fabricator and material supplier are required to determine if the PCB is using a design that requires a license. There are 2 primary considerations:

  1. If the design is using a buried capacitance technology, YES, a license is required by both the fabricator and material supplier. This buried capacitanceTM technology, has been patented and Sanmina-SCI holds the rights to this type of PCB design. Only licensed PCB fabricators may build “shared” planar buried capacitanceTM PCB’s and only licensed material providers can sell PCB materials for “shared” capacitanceTM applications. A list of licensed PCB fabricators is available at http://www.sanmina-sci.com/Solutions/pcb_resource.html . (FaradFlex® from Oak-Mitsui IS a “shared” planar buried capacitanceTM licensed material).
  2. If the design is for a “discrete” embedded capacitor application or if is used as a signal layer then there is usually NO REQUIREMENT for a license.

>back to top

How many capacitors can be removed by using FaradFlex®?
Since every design is custom there is no clear rule to determine the exact amount of capacitors that can be removed. There is significant data that shows the amount of capacitance needed in the FaradFlex® laminate can be as little as 1% or less than the amount that can be removed by eliminating the capacitors from the surface. This is primarily due to the fact that the thin FaradFlex® laminate has magnitudes less impedance and a very small inductance loop for power delivery. Also, at frequencies above 200 MHz the surface capacitors do not have time to deliver their charge in many cases they are acting mostly as inductors rather than capacitors. There are case studies showing hundreds and even thousands of bypass capacitors coming off one PCB. 
>back to top

What is the impact on the cost of the PCB/ PCBA/ System?
Since every design is custom there is no clear rule to determine the exact cost of using FaradFlex®. It is true that FaradFlex® typically costs more that standard FR-4 materials used in PCBs. Even so, there are many tools available today showing how the technical, performance, and design benefits allow the PCBA and in many cases the PCB to cost less! We at Oak Mitsui Technologies encourage you to contact us to help determine what your cost impact will be.  Click here for our Cost Benefit Anaylisis Form.
>back to top

Is FaradFlex® robust to lead free processing?
FaradFlex® has passed most or all of the electronics industry and IPC thermal reliability tests including those at “lead-free” conditions. FaradFlex® is also much more robust to thermal stresses than typical high temperature, high Tg phenolic cured FR-4 materials used in PCBs.
>back to top

Can PCB shops process ultra thin materials with out added cost?
Since FaradFlex® is typically processed as a power-ground layer, it is normally very rigid in conveyor processing and innerlayer processes and performs the same as other PCB materials. Since there is no fiber glass cloth to damage and a flexible epoxy, the FaradFlex® MC24 laminate actually has better yields than FR-4. In other cases, the thinner FaradFlex® laminates may be processed by attaching a rigid leader or frame to allow easy transport in the innerlayer conveyors. Typically, this is one of the few or only process changes necessary and the cost is minimal. 
>back to top

What PCB shops can use FaradFlex®?

  1. For “shared” buried capacitanceTM technology, there is a list of licensed PCB fabricators available at http://www.sanmina-sci.com/Solutions/pcb_resource.html .
  2. For discrete buried capacitanceTM or other applications ANY PCB fabricator can use FaradFlex® with no license requirement.

>back to top

What materials are compatible with FaradFlex®?
So far, FaradFlex® is compatible with all of the most common commercially available FR-4 materials. Also, there are many applications using ISOLA, NELCO, PANASONIC and other high performance materials. There are also current studies evaluating the compatibility and benefits of using FaradFlex® with materials from Rogers, Taconic, Arlon and others.
>back to top

80 First Street, Hoosick Falls, New York 12090 • Phone (518) 686-4961
Copyright © 2014 Oak-Mitsui